search

Silvercrest SKAS 1000 A16 Specifications Page 57

  • Download
  • Add to my manuals
  • Print
  • Page
    / 192
  • Table of contents
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 56
Section 2
Fault Code Diagnostics
48
159 9F Range position sensor signal leaves
engaged position during driving
Using TransSoft, verify that the range position sensor
counts are outside of the nominal range: 80 to 130 or
490 to 590.
The measured values should not drift or show signal
disturbances after range shifting. Values outside range,
exchange main transmission. If error occurs
sporadically: When submitting a warranty claim under
standard warranty conditions, the complete TCU should
be replaced and the entire unit submitted with warranty
claim. Out-of-warranty only and/or no warranty claim
submitted, replace the lower part of TCU.
For assistance contact OnTrac at 866-668-7221 and ask
for a transmission specialist.
160 A0 Splitter position sensor signal leaves
engaged position during driving
Using TransSoft, verify that the splitter position sensor
counts are outside of the nominal range: 70 to 140 or
500 to 620.
The measured values should not drift or show signal
disturbances after splitter shifting. Values outside range,
exchange main transmission. If error occurs
sporadically: When submitting a warranty claim under
standard warranty conditions, the complete TCU should
be replaced and the entire unit submitted with warranty
claim.
Out-of-warranty only and/or no warranty claim
submitted, replace the lower part of TCU.
For assistance, contact OnTrac at 866-668-7221 and ask
for a transmission specialist.
163 A3 Engine does not react to torque
intervention
The ECM did not react correctly to an SAE J1939
message. Follow your OEM’s SAE J1939 diagnostic
procedures to correct for a fault SAE J1939 data link.
Check for engine codes that would cause the engine to
go into derate mode. (Fuel restriction, air restriction,
high temp, low coolant etc).
164 A4 The main TCU has not received
communication from the engine. Error
on driver’s demand engine percent
torque message: EEC1
The TCU received the SAE J1939 message from the ECM
but the information within the message was not within
specifications. Verify that the ECM software level is
approved with the ZF-FreedomLine transmission and
that all settings are correct.
If necessary, contact OnTrac at 866-668-7221 and request
a ZF-FreedomLine transmission specialist.
165 A5 The main TCU has not received
communication from the engine. Error
on accelerator pedal position message:
EEC2
The TCU received the SAE J1939 message from the ECM
but the information within the message was not within
specifications. Verify that the ECM software level is
approved with the ZF-FreedomLine transmission and
that all settings are correct.
If necessary, contact OnTrac at 866-668-7221 and request
a ZF-FreedomLine transmission specialist.
ISO Fault Code Diagnostics
NOTE: ISO display codes may not be available on vehicles built prior to January 2006.
ISO Fault
Identifier
ISO Display
Fault Codes
(J587 Display) Fault Description
Repair Instructions
NOTE: The following repair instructions pertain to
active faults only. For information and instructions
about inactive faults, please contact OnTrac at
866-668-7221 and request a transmission
specialist.
Page view 56
1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 191 192

Comments to this Manuals

No comments
Related products and manuals for Coffee makers Silvercrest SKAS 1000 A16
Coffee makers Silvercrest SEM 1100 A2 User Manual   (70 pages)
  • Olympia Fat Cat Industrial-injection Ultra Disk FireMagic
  • Billy Goat Security device components Cambridge Audio Plasma TVs Asus Access control readers RCA Headsets Radio Shack Alarm clocks
  • Powermate PM0105007 GE RV60 Magnavox 50ME313V Olympus TELECONVERTER EC-14 Siemens IC60
  • Whirlpool ACM 918/BA Instruction for Use Aeg L71060SL User Manual ProCurve 2610-PWR Specifications Asus Xonar Essence ST User Manual Neff B45E42N3RU User Manual