Silvercrest SKD 2300 A1 User Manual Page 45
- Page / 62
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SKD2300A1 43
3. Press the “Reduce temperature”
button 17 to lower the desired
temperature to a minimum of 5 °C
(41 °F).
Selected specified temperature 20 is
shown in display 5.
6.3 Setting the heat setting
The appliance has three heat settings:
– 1,000 watts
– 1,300 watts
– 2,300 watts
1. Press button 25 repeatedly until the
desired heat setting is set.
Selected heating level 11 is shown in
display 5.
2. Press the fan button 15 to switch the fan
on or off.
If the fan is switched on, "Fan"
symbol 12 is shown in display 5.
Note: The fan might make a slight
noise, but it does ensure better
circulation of the heated air.
6.4 Setting the heating time
The appliance has a timer for setting the
heating time to between 1 and 15 hours.
The appliance switches off automatically
once the heating time has expired.
1. Press timer button 18 repeatedly until
desired running time 19 is shown in
display 5.
2. To switch off the timer, press timer
button 18 repeatedly until running
time 19 is no longer displayed.
6.5 Thermal cut-out
For your safety the appliance has a thermal
cut-out.
If the temperature inside the appliance
becomes too high, the appliance switches
off automatically:
1. Switch the mains switch 9 to "0" to
switch off the appliance.
2. Check whether the air inlet 6 or outlet 4
is obstructed and remove the cause.
If you cannot establish a cause and the
fault occurs repeatedly, have the
appliance repaired or else take it out of
use.
3. Wait for the appliance to cool down.
4. You can then continue to operate it
normally.
6.6 Frost protection
To prevent the temperature in a room falling
below 0°C (32°F), proceed as follows:
1. Press the button for selecting heating
level 25 repeatedly until "Frost
protection" symbol 13 appears in
display 5.
As soon as the temperature in the immediate
vicinity of the appliance drops significantly
below 7 °C (44 °F), the heating
automatically switches on.
As soon as the temperature rises to above
9 °C (48 °F), the heating switches off and
display 5 shows room temperature again.
2. To switch off frost protection, press the
button for selecting heating level 25
repeatedly until "Frost protection"
symbol 13 in display 5 disappears.
RP90866 Konvektor LB5 Seite 43 Dienstag, 2. Juli 2013 3:39 15
- IAN 90866 1
- 1. Descripción del aparato 4
- 3. Datos técnicos 5
- 4. Indicaciones de seguridad 6
- SKD2300A1 5 7
- 4.7 Manejo de las pilas 8
- 4.8 Daños materiales 9
- 5.1 Montar el aparato 9
- 5.2 Instalar el aparato 9
- 5.3 Colocar las pilas 9
- 6. Manejo 10
- SKD2300A1 9 11
- 7. Limpieza 12
- 8. Solución de averías 12
- 9. Eliminación 13
- Alcance de la garantía 14
- Centro de servicio técnico 15
- Proveedor 15
- 1.1 Impiego previsto 16
- 1.2 Entità della fornitura 16
- 3. Dati tecnici 17
- 4. Indicazioni di sicurezza 18
- 4.4 Protezione dagli incendi 19
- 4.5 Protezione da lesioni 20
- 4.8 Danni materiali 21
- 5.1 Montare l’apparecchio 21
- 6. Funzionamento 22
- 7. Pulizia 23
- 8. Risoluzione dei problemi 24
- 9. Smaltimento 24
- 9.3 Imballaggio 25
- Svolgimento della garanzia 26
- Centro d’assistenza 26
- Fornitore 26
- 1. Descrição do aparelho 27
- 3. Dados técnicos 28
- 4. Indicações de segurança 28
- 4.2 Notas genéricas 29
- 4.7 Manuseamento das pilhas 31
- 4.8 Danos materiais 31
- 5.1 Montar o aparelho 32
- 5.2 Instalar o aparelho 32
- 5.3 Colocar as pilhas 32
- 6. Operar 33
- 7. Limpar 35
- 8. Resolução de problemas 35
- 9. Eliminação 36
- Âmbito da garantia 37
- Service-Center 38
- Fornecedor 38
- Contents 39
- 1. Description 39
- 3. Technical data 40
- 4. Safety information 40
- SKD2300A1 39 41
- 4.5 Protection against injury 42
- 4.7 Handling batteries 43
- 4.8 Material damage 43
- 5.1 Mounting the appliance 43
- 5.2 Setting up the appliance 43
- 6. Operating 44
- 6.3 Setting the heat setting 45
- 6.4 Setting the heating time 45
- 6.5 Thermal cut-out 45
- 6.6 Frost protection 45
- 7. Cleaning 46
- 8. Troubleshooting 46
- 9. Disposal 47
- Scope of warranty 48
- Warranty process 48
- Service Centre 49
- Supplier 49
- 1. Gerätebeschreibung 50
- 3. Technische Daten 51
- 4. Sicherheitshinweise 52
- 4.4 Schutz vor Brandgefahr 53
- 4.5 Schutz vor Verletzungen 54
- 4.7 Umgang mit Batterien 54
- 4.8 Sachschäden 55
- 5.1 Gerät montieren 55
- 5.2 Gerät aufstellen 55
- 5.3 Batterie einlegen 55
- 6. Bedienen 56
- 6.4 Heizdauer einstellen 57
- 6.5 Überhitzungsschutz 57
- 6.6 Frostschutz 57
- 7. Reinigen 58
- 8. Störungen beheben 58
- 9. Entsorgung 59
- Garantiezeit und gesetzliche 60
- Mängelansprüche 60
- Garantieumfang 60
- Abwicklung im Garantiefall 60
- Service-Center 61
- Lieferant 61
Related products and manuals for Radiators Silvercrest SKD 2300 A1
Radiators Silvercrest SWUB 85 B2 User Manual
(45 pages)
(45 pages)
Radiators Silvercrest SHK 100 C3 User Manual
(44 pages)
(44 pages)
Radiators Silvercrest SFW 100 B2 User Manual
(29 pages)
(29 pages)
Radiators Silvercrest SFW 100 B2 User Manual
(37 pages)
(37 pages)
Radiators Silvercrest SFW 100 B2 User Manual
(45 pages)
(45 pages)
Radiators Silvercrest SFW 100 B2 User Manual
(61 pages)
(61 pages)
Radiators Silvercrest SWD 100 B2 User Manual
(21 pages)
(21 pages)
Radiators Silvercrest SWD 100 B2 User Manual
(44 pages)
(44 pages)
© 2020, manymanuals.com. All rights reserved. | 0.778 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals