Silvercrest SPLK 200 A1 Instruction Manual download pdf (Page 67)

■ There’s no sound

■ There’s no video

■ The AV receiver’s remote controller doesn’t

control your iPod

■ The AV receiver unexpectedly selects your iPod

as the input source

■ Can’t record

■ There’s no sound

■ The Zone 2 speakers produce no sound

■ The sound changes when I connect my

headphones

■ The speaker distance cannot be set as required

■ How do I change the language of a multiplex

source

■ The u functions don’t work

■ The functions System On/Auto Power On and

Direct Change don’t work for components

connected via u

■ When performing “Audyssey 2EQ

Room

Correction and Speaker Setup”, the

measurement fails showing the message

“Ambient noise is too high.”.

To control an Onkyo component that’s not connected

via u, point the remote controller at the compo-

nent. Be sure to enter the appropriate remote control

code first.

The entered remote control code may not be correct.

If more than one code is listed, try each one.

—

UP-A1 Dock for iPod

Make sure your iPod is actually playing. —

Make sure your iPod is inserted properly in the

Dock.

—

Make sure the UP-A1 Dock is connected to the UNI-

VERSAL PORT jack on the AV receiver.

—

Make sure the AV receiver is turned on, the correct

input source is selected, and the volume is turned up.

—

Make sure the plugs are pushed in all the way. —

Try resetting your iPod. —

Make sure that your iPod model’s TV OUT setting is

set to On.

—

Make sure the correct input is selected on your TV or

the AV receiver.

—

Some versions of the iPod do not output video. —

Make sure your iPod is properly inserted in the

Dock. If your iPod is in a case, it may not connect

properly to the Dock. Always remove your iPod

from the case before inserting it into the Dock.

—

The iPod cannot be operated while it’s displaying the

Apple logo.

—

Make sure you’ve selected the right remote mode. —

When you use the AV receiver’s remote controller,

point it toward your AV receiver.

—

When connecting UP-A1 Dock to the radio tuner

UP-HT1 with AUTO selected by the tuner’s Mode

Selector switch, you can switch the input source

between UP-A1 Dock and the tuner, by pressing

PORT repeatedly on the front panel.

—

If you still can’t control your iPod, start playback by

pressing your iPod model’s Play button. Remote

operation should then be possible.

—

Try resetting your iPod. —

Depending on your iPod, some buttons may not

work as expected.

—

Always pause iPod playback before selecting a dif-

ferent input source. If playback is not paused, the

Direct Change function may select your iPod as the

input source by mistake during the transition

between tracks.

—

Recording

On your recorder, make sure the correct input is

selected.

—

To prevent signal loops and damage to the AV

receiver, input signals are not fed through to outputs

with the same name (VCR/DVR IN to VCR/DVR

OUT).

—

Zone 2

Only components connected to analog inputs can be

played in Zone 2.

—

To use the Zone 2 speakers, you must set the “Front

High/Zone2” setting to “Zone2” .

Others

When a pair of headphones is connected, the listen-

ing mode is set to Stereo, unless it’s already set to

Stereo, Mono or Direct.

—

In some cases, corrected values suitable for home

theater use may be set automatically.

—

Use the “Multiplex” setting on the “Audio Adjust”

menu to select “Main” or “Sub”.

To use u, you must make an u connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected dig-

itally.

These functions don’t work when Zone 2 is turned

on.

This can be caused by any malfunction in your

speaker unit. Check if the unit produces normal

sounds.

—

1 2 ... 62 63 64 65 66 67 68 69 70 71 72 ... 98 99

Comments to this Manuals

No comments

Silvercrest SPLK 200 A1 Instruction Manual Page 67

Comments to this Manuals