Silvercrest SPU 900 A1 Service Manual download pdf (Page 11)

- 9 -

Radiooperation

The technical data of the appliance makes

possible an adjustable frequency range wider

than the permitted frequency ranges of 87,5 -

108 MHz resp. 526,5 - 1606,5 kHz. In some

countries, dierent national regulations may

apply to the assigned radio frequency ranges.

Please note that information received outside

of the assigned radio frequency ranges may

not be used, passed on to third parties or

otherwise misused. For VHF radio reception,

completely unwind the wire aeriel 2) and, with

the radio switched on, determine the most fa-

vourable positioning for it. The appliance has

a built-in aerial for MW reception. To improve

MW reception, if required, turn the radio until

it is in the most favourable position.

Switching the radio on and off

1. Press the button

l. In the display g

the current frequency and the switch-on

symbol

is indicated. Next to it, the

clock symbol blinks and thus indicates

that the device is waiting for the reception

of the current time from an RDS station.

2. Press the button

lonce again to

switch the radio function o and return the

appliance to the standby mode.

Manual station selection

1. Use the waveband select button u to

select the required reception waveband,

MW (AM) or VHF (FM).

2. Press the button UP o to search for radio

stations with a frequency higher than the

one indicated in the display.

3. Press the button DOWN i to search for

radio stations with a frequency lower than

the one indicated in the display.

4. If the found radio station transmits RDS-

Data, the indicator in the dis-

play g glows. The display g indicates

the name of the radio station and the time

is updated (insofar as this adjustment is

activated, see the section "Programme the

Update function").

Automatic station search

You can also let the appliance search for

radio stations. The radio alarm then searches

the selected frequency range until it has

found a radio station.

1. Press and hold the button UP o for two

seconds: The radio alarm searches for the

station with the next highest frequency.

2. Press and hold the button DOWN i for

two seconds: The radio alarm searches

for the station with the next lowest fre-

quency.

Repeat these steps until you have found a

radio station to your liking.

Programming stations

For each of 2 users you can save 20 VHF sta-

tions and 12 MW stations as favourites in the

appliance. These memory slots are spread

over several pages, which can be called up

via the PAGE/AL.SET button f. On each

page there are 4 Sender slots, they can be

addressed with the PRESET/ALARM +/-but-

tons s/d.

1. With the radio switched on, press the

PAGE/AL.SET button f to call up the

desired memory page 1-5. In the display

g the number of the just selected memory

page appears below "PAGE".

2. Tune in to the desired station.

3. Briey press the button A.M.S. MEMORY

h. In the display g the number and the

memory slot indicator "MEM" blink.

4. Now, using the PRESET/ALARM +/— but-

tons s/d, select the place at which the

radio station is to be saved. Conrm it

with the A.M.S. MEMORY button h. The

radio station is now saved and will be

permanently indicated.

5. As the appliance can be used by several

people, it is equipped with user switching.

Both users can thus save dierent radio

stations as favourites. To switch over to

the individual user, press and hold the

NAP|USER button k for two seconds.

BDA_SPU 900 A1 - DT-67087_4_en.indd 9 19.07.2011 17:30:09

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 75 76

Comments to this Manuals

No comments

Silvercrest SPU 900 A1 Service Manual Page 11

Comments to this Manuals

Related products and manuals for Wall clocks Silvercrest SPU 900 A1