Silvercrest STG 70 B3 User Manual download pdf (Page 6)

3. Transport

DANGER! Please make sure that the refrigerant cir-

cuit 9 (lines on the interior and on the rear of the ap-

pliance, compressor 14) is not damaged.

WARNING! Do not tilt the appliance further than 45°.

4. Using for the first time

Removing packaging

• Remove the packaging material and adhesive strips.

• Remove the foam parts in the interior.

Checking for damage

• Check the appliance for damage, especially the refriger-

ant circuit 9 (lines on the interior and on the rear of the

appliance, compressor 14) and the power cable 15.

DANGER! Do not connect the appliance if it is dam-

aged.

Cleaning before first use

• Clean the appliance as described in section "Defrosting

and cleaning" on page 6.

Positioning

DANGER! Position this appliance in a room with a

capacity of at least 4.5 m

. In the event of a leak in

the refrigerant circuit, an inflammable mix of refriger-

ant and air may form in rooms that are too small.

• The compressor 14 and the side walls of the appliance

become hot during operation and require good ventilation

all around the appliance. Therefore please observe the

following minimum clearances:

- at the rear: 10 cm;

- at the sides: 10 cm.

• Position the appliance in a well-ventilated, dry room.

Place it on level, solid ground.

• This appliance complies with the climate classifications

SN, N, ST and T and so is intended for an ambient tem-

perature of +10 °C to +43 °C.

Position the appliance in a location with a suitable ambi-

ent temperature.

• When positioning, avoid the following:

- direct sunlight,

- proximity to heat sources such as an oven or radiators.

• If the nature of your premises require it, you can reverse

the door fittings. See section "Reversing the door fittings"

on page 7.

Aligning

To ensure the flawless function of the appliance and air-tight

closure of the door seals, the appliance must be aligned

straight. For this purpose, two height-adjustable feet 12 are

provided at the front.

1. Have a second person raise the freezer slightly at the

front.

2. Increasing the height of the foot: Turn the foot clock-

wise. Please note that the feet can also be unscrewed

completely.

Decreasing the height of the foot: Turn the foot anti-

clockwise.

Connecting

DANGER! Do not connect the appliance until it is lo-

cated in its final position and has been aligned

straight.

WARNING! After moving the appliance, allow it to stand for at

least 24 hours so that the refrigerant circuit can settle.

DANGER! Connect the appliance to a wall socket

with protective contacts, where the technical data

match those of the appliance (see rating plate 13).

• Do not use any extension cables or multiple sockets.

• The wall socket must also be easily accessible after con-

nection. If this is not possible on your premises, it must

always be possible to disconnect the appliance from the

mains, for instance with the fuse.

5. Operation

•

Use the temperature controller

SET

1 to change between

3 temperature ranges. The LEDs next to LOW, MID and

HIGH 2 indicate, which level is activated. Switch by

pressing the SET button.

Switching on and off

• To switch on and off, press the button 6. This also

switches on or off an LED, which is located next to LOW,

MID or HIGH 2.

• If the alarm sounds after 1 minute and the ALARM LED 3

lights up, press the ALARM/SUPER button 4 for 3 sec-

onds to switch the acoustic alarm off. The ALARM LED

remains until the operating temperature is reached.

• When using the device for the first time and after defrost-

ing activate the Superfrost function. For this purpose,

press the ALARM/SUPER button 4 briefly. The SUPER

LED 5 remains lit as long as the function is active. The

function is switched off automatically when the average

temperature of the past 30-65 hours was -27 °C to

-30 °C.

• To monitor the temperature, you require a freezing ther-

mometer. The normal operating temperature for the

freezer is -18 °C.

• The temperature setting that you require depends on var-

ious factors, such as the ambient temperature.

• For normal operation, select a setting between the tem-

perature levels LOW, MID and HIGH 2 by pressing the

SET 1 button. Here, the temperature level LOW repre-

sents the hottest temperature, and temperature level

HIGH the coldest.

• In most cases, the temperature level MID corresponds to

the normal operating temperature of -18 °C.

• After setting, monitor the temperature for several hours

with a freezing thermometer. Repeat this check from time

to time and change this setting, if necessary.

__RP71979_B6.book Seite 4 Freitag, 23. März 2012 2:21 14

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Silvercrest STG 70 B3 User Manual Page 6

Comments to this Manuals

Related products and manuals for Refrigerators Silvercrest STG 70 B3